Part of the  

Solid State Technology

  and   

The Confab

  Network

About  |  Contact

Posts Tagged ‘interconnect’

Air-Gaps for FinFETs Shown at IEDM

Friday, October 28th, 2016

thumbnail

By Ed Korczynski, Sr. Technical Editor

Researchers from IBM and Globalfoundries will report on the first use of “air-gaps” as part of the dielectric insulation around active gates of “10nm-node” finFETs at the upcoming International Electron Devices Meeting (IEDM) of the IEEE (ieee-iedm.org). Happening in San Francisco in early December, IEDM 2016 will again provide a forum for the world’s leading R&D teams to show off their latest-greatest devices, including 7nm-node finFETs by IBM/Globalfoundries/Samsung and by TSMC. Air-gaps reduce the dielectric capacitance that slows down ICs, so their integration into transistor structures leads to faster logic chips.

History of Airgaps – ILD and IPD

As this editor recently covered at SemiMD, in 1998, Ben Shieh—then a researcher at Stanford University and now a foundry interface for Apple Corp.—first published (Shieh, Saraswat & McVittie. IEEE Electron Dev. Lett., January 1998) on the use of controlled pitch design combined with CVD dielectrics to form “pinched-off keyholes” in cross-sections of inter-layer dielectrics (ILD).

In 2007, IBM researchers showed a way to use sacrificial dielectric layers as part of a subtractive process that allows air-gaps to be integrated into any existing dielectric structure. In an interview with this editor at that time, IBM Fellow Dan Edelstein explained, “we use lithography to etch a narrow channel down so it will cap off, then deliberated damage the dielectric and etch so it looks like a balloon. We get a big gap with a drop in capacitance and then a small slot that gets pinched off.

Intel presented on their integration of air-gaps into on-chip interconnects at IITC in 2010 but delayed use until the company’s 14nm-node reached production in 2014. 2D-NAND fabs have been using air-gaps as part of the inter-poly dielectric (IPD) for many years, so there is precedent for integration near the gate-stack.

Airgaps for finFETs

Now researchers from IBM and Globalfoundries will report in (IEDM Paper #17.1, “Air Spacer for 10nm FinFET CMOS and Beyond,” K. Cheng et al) on the first air-gaps used at the transistor level in logic. Figure 1 shows that for these “10nm-node” finFETs the dielectric spacing—including the air-gap and both sides of the dielectric liner—is about 10 nm. The liner needs to be ~2nm thin so that ~1nm of ultra-low-k sacrificial dielectric remains on either side of the ~5nm air-gap.

Fig.1: Schematic of partial air-gaps only above fin tops using dielectric liners to protect gate stacks during air-gap formation for 10nm finFET CMOS and beyond. (source: IEDM 2016, Paper#17.1, Fig.12)

These air-gaps reduced capacitance at the transistor level by as much as 25%, and in a ring oscillator test circuit by as much as 15%. The researchers say a partial integration scheme—where the air-gaps are formed only above the tops of fin— minimizes damage to the FinFET, as does the high-selectivity etching process used to fabricate them.

Figure 2 shows a cross-section transmission electron micrograph (TEM) of what can go wrong with etch-back air-gaps when all of the processes are not properly controlled. Because there are inherent process:design interactions needed to form repeatable air-gaps of desired shapes, this integration scheme should be extendable “beyond” the “10-nm node” to finFETs formed at tighter pitches. However, it seems likely that “5nm-node” logic FETs will use arrays of horizontal silicon nano-wires (NW), for which more complex air-gap integration schemes would seem to be needed.

Fig.2: TEM image of FinFET transistor damage—specifically, erosion of the fin and source-drain epitaxy—by improper etch-back of the air-gaps at 10nm dimensions. (source: IEDM 2016, Paper#17.1, Fig.10)

—E.K.

Leti’s CoolCube 3D Transistor Stacking Improves with Qualcomm Help

Wednesday, April 27th, 2016

By Ed Korczynski, Sr. Technical Editor

As previously covered by Solid State Technology CEA-Leti in France has been developing monolithic transistor stacking based on laser re-crystallization of active silicon in upper layers called “CoolCube” (TM). Leading mobile chip supplier Qualcomm has been working with Leti on CoolCube R&D since late 2013, and based on preliminary results have opted to continue collaborating with the goal of building a complete ecosystem that takes the technology from design to fabrication.

“The Qualcomm Technologies and Leti teams have demonstrated the potential of this technology for designing and fabricating high-density and high-performance chips for mobile devices,” said Karim Arabi, vice president of engineering, Qualcomm Technologies, Inc. “We are optimistic that this technology could address some of the technology scaling issues and this is why we are extending our collaboration with Leti.” As part of the collaboration, Qualcomm Technologies and Leti are sharing the technology through flexible, multi-party collaboration programs to accelerate adoption.

Olivier Faynot, micro-electronic component section manager of CEA-Leti, in an exclusive interview with Solid State Technology and SemiMD explained, “Today we have a strong focus on CMOS over CMOS integration, and this is the primary integration that we are pushing. What we see today is the integration of NMOS over PMOS is interesting and suitable for new material incorporation such as III-V and germanium.”

Table: Critical thermal budget steps summary in a planar FDSOI integration and CoolCube process for top FET in 3DVLSI. (Source: VLSI Symposium 2015)

The Table shows that CMOS over CMOS integration has met transistor performance goals with low-temperature processes, such that the top transistors have at least 90% of the performance compared to the bottom. Faynot says that recent results for transistors are meeting specification, while there is still work to be done on inter-tier metal connections. For advanced ICs there is a lot of interconnect routing congestion around the contacts and the metal-1 level, so inter-tier connection (formerly termed the more generic “local interconnect”) levels are needed to route some gates at the bottom level for connection to the top level.

“The main focus now is on the thermal budget for the integration of the inter-tier level,” explained Faynot. “To do this, we are not just working on the processing but also working closely with the designers. For example, depending on the material chosen for the metal inter-tier there will be different limits on the metal link lengths.” Tungsten is relatively more stable than copper, but with higher electrical resistance for inherently lower limits on line lengths. Additional details on such process-design co-dependencies will be disclosed during the 2016 VLSI Technology Symposium, chaired by Raj Jammy.

When the industry decides to integrate III-V and Ge alternate-channel materials in CMOS, the different processing conditions for each should make NMOS over PMOS CoolCube a relatively easy performance extension. “Three-fives and germanium are basically materials with low thermal budgets, so they would be most compatible with CoolCube processing,” reminded Faynot. “To me, this kind of technology would be very interesting for mobile applications, because it would achieve a circuit where the length of the wires would be shortened. We would expect to save in area, and have less of a trade-off between power-consumption and speed.”

“This is a new wave that CoolCube is creating and it has been possible thanks to the interest and support of Qualcomm Technologies, which is pushing the technological development in a good direction and sending a strong signal to the microelectronics community,” said Leti CEO Marie Semeria. “Together, we aim to build a complete ecosystem with foundries, equipment suppliers, and EDA and design houses to assemble all the pieces of the puzzle and move the technology into the product-qualification phase.”

—E.K.

3DIC Technology Drivers and Roadmaps

Monday, June 22nd, 2015

thumbnail

By Ed Korczynski, Sr. Technical Editor

After 15 years of targeted R&D, through-silicon via (TSV) formation technology has been established for various applications. Figure 1 shows that there are now detailed roadmaps for different types of 3-dimensional (3D) ICs well established in industry—first-order segmentation based on the wiring-level/partitioning—with all of the unit-processes and integration needed for reliable functionality shown. Using block-to-block integration with 5 micron lines at leading international IC foundries such as GlobalFoundries, systems stacking logic and memory such as the Hybrid Memory Cube (HMC) are now in production.

Fig. 1: Today’s 3D technology landscape segmented by wiring-level, showing cross-sections of typical 2-tier circuit stacks, and indicating planned reductions in contact pitches. (Source: imec)

“There are interposers for high-end complex SOC design with good yield,” informed Eric Beyne, Scientific Director Advanced Packaging & Interconnect for imec in an exclusive interview with Solid State Technology. ““For a systems company, once you’ve made the decision to go 3D there’s no way back,” said Beyne. “If you need high-bandwidth memory, for example, then you’re committed to some sort of 3D. The process is happening today.” Beyne is scheduled to talk about 3D technology driven by 3D application requirements in the imec Technology Forum to be held July 13 in San Francisco.

Adaptation of TSV for stacking of components into a complete functional system is key to high-volume demand. Phil Garrou, packaging technologist and SemiMD blogger, reported from the recent ConFab that Hynix is readying a second generation of high-bandwidth memory (HBM 2) for use in high performance computing (HPC) such as graphics, with products already announced like Pascal from Nvidia and Greenland from AMD.

For a normalized 1 cm2 of silicon area, wide-IO memory needs 1600 signal pins (not counting additional power and ground pins) so several thousand TSV are needed for high-performance stacked DRAM today, while in more advanced memory architectures it could go up by another factor of 10. For wide-IO HVM-2 (or Wide-IO2) the silicon consumed by IO circuitry is maybe 6 cm2 today, such that a 3D stack with shorter vertical connections would eliminate many of the drivers on the chip and would allow scaling of the micro-bumps to perhaps save a total of 4 cm2 in silicon area. 3D stacks provide such trade-offs between design and performance, so the best results are predicted for 3DICs where the partitioning can be re-done at the gate or transistor level. For example, a modern 8-core microprocessor could have over 50% of the silicon area consumed by L3-cache-memory and IO circuitry, and moving from 2D to 3D would reduce total wire-lengths and interconnect power consumptions by >50%.

There are inherent thresholds based on the High:Width ratio (H:W) that determine costs and challenges in process integration of TSV:

-    10:1 ratio is the limit for the use of relatively inexpensive physical vapor deposition (PVD) for the Cu barrier/seed (B/S),

-    20:1 ratio is the limit for the use of atomic-layer deposition (ALD) for B/S and electroless deposition (ELD) for Cu fill with 1.5 x 30 micron vias on the roadmap for the far future,

-    30:1 ratio and greater is unproven as manufacturable, though novel deposition technologies continue to be explored.

TSV Processing Results

The researchers at imec have evaluated different ways of connecting TSV to underlying silicon, and have determined that direct connections to micro-bumps are inherently superior to use of any re-distribution layer (RDL) metal. Consequently, there is renewed effort on scaling of micro-bump pitches to be able to match up with TSV. The standard minimum micro-bump pitch today of 40 micron has been shrunk to 20, and imec is now working on 10 micron with plans to go to 5 micron. While it may not help with TSV connections, an RDL layer may still be needed in the final stack and the Cu metal over-burden from TSV filling has been shown by imec to be sufficiently reproducible to be used as the RDL metal. The silicon surface area covered by TSV today is a few percents not 10s of percents, since the wiring level is global or semi-global.

Regarding the trade-offs between die-to-wafer (D2W) and wafer-to-wafer (W2W) stacking, D2W seems advantageous for most near-term solutions because of easier design and superior yield. D2W design is easier because the top die can be arbitrarily smaller silicon, instead of the identically sized chips needed in W2W stacks. Assuming the same defectivity levels in stacking, D2W yield will almost always be superior to W2W because of the ability to use strictly known-good-die. Still, there are high-density integration concepts out on the horizon that call for W2W stacking. Monolithic 3D (M3D) integration using re-grown active silicon instead of TSV may still be used in the future, but design and yield issues will be at least comparable to those of W2W stacking.

Beyne mentioned that during the recent ECTC 2015, EV Group showed impressive 250nm overlay accuracy on 450mm wafers, proving that W2W alignment at the next wafer size will be sufficient for 3D stacking. Beyne is also excited by the fact the at this year’s ECTC there was, “strong interest in thermo-compression bonding, with 18 papers from leading companies. It’s something that we’ve been working on for many years for die-to-wafer stacking, while people had mistakenly thought that it might be too slow or too expensive.”

Thermal issues for high-performance circuitry remain a potential issue for 3D stacking, particularly when working with finFETs. In 2D transistors the excellent thermal conductivity of the underlying silicon crystal acts like a built-in heat-sink to diffuse heat away from active regions. However, when 3D finFETs protrude from the silicon surface the main path for thermal dissipation is through the metal lines of the local interconnect stack, and so finFETs in general and stacks of finFETs in particular tend to induce more electro-migration (EM) failures in copper interconnects compared to 2D devices built on bulk silicon.

3D Designs and Cost Modeling

At a recent North California Chapter of the American Vacuum Society (NCCAVS) PAG-CMPUG-TFUG Joint Users Group Meeting discussing 3D chip technology held at Semi Global Headquarters in San Jose, Jun-Ho Choy of Mentor Graphics Corp. presented on “Electromigration Simulation Flow For Chip-Scale Parametric Failure Analysis.” Figure 2 shows the results from use of a physics-based model for temperature- and residual-stress-aware void nucleation and growth. Mentor has identified new failure mechanisms in TSV that are based on coefficient of thermal expansion (CTE) mismatch stresses. Large stresses can develop in lines near TSV during subsequent thermal processing, and the stress levels are layout dependent. In the worst cases the combined total stress can exceed the critical level required for void nucleation before any electrical stressing is applied. During electrical stress, EM voids were observed to initially nucleate under the TSV centers at the landing-pad interfaces even though these are the locations of minimal current-crowding, which requires proper modeling of CTE-mismatch induced stresses to explain.

Fig. 2: Calibration of an Electronic Design Automation (EDA) tool allows for accurate prediction of transistor performance depending on distance from a TSV. (Source: Mentor Graphics)

Planned for July 16, 2015 at SEMICON West in San Francisco, a presentation on “3DIC Technology Past, Present and Future” will be part of one of the side Semiconductor Technology Sessions (STS). Ramakanth Alapati, Director of Packaging Strategy and Marketing, GLOBALFOUNDRIES, will discuss the underlying economic, supply chain and technology factors that will drive productization of 3DIC technology as we know it today. Key to understanding the dynamic of technology adaptation is using performance/$ as a metric.

5nm Node Needs EUV for Economics

Thursday, January 29th, 2015

thumbnail

By Ed Korczynski, Sr. Technical Editor

#mce_temp_url#

At IEDM 2014 last month in San Francisco, Applied Materials sponsored an evening panel discussion on the theme of “How do we continue past 7nm?” Given that leading fabs are now ramping 14nm node processes, and exploring manufacturing options for the 10nm node, “past 7nm” means 5nm node processing. There are many device options possible, but cost-effective manufacturing at this scale will require Extreme Ultra-Violet (EUV) lithography to avoid the costs of quadruple-patterning.

Fig. 1: Panelists discuss future IC manufacturing and design possibilities in San Francisco on December 16, 2014. (Source: Pete Singer)

Figure 1 shows the panel being moderated by Professor Mark Rodwell of the University of California Santa Barbara, composed of the following industry experts:

  • Karim Arabi, Ph.D. – vice president, engineering, Qualcomm,
  • Michael Guillorn, Ph.D. – research staff member, IBM,
  • Witek Maszara, Ph.D. – distinguished member of technical staff, GLOBALFOUNDRIES,
  • Aaron Thean, Ph.D. – vice president, logic process technologies, imec, and
  • Satheesh Kuppurao, Ph.D. – vice president, front end products group, Applied Materials.

Arabi said that from the design perspective the overarching concern is to keep “innovating at the edge” of instantaneous and mobile processing. At the transistor level, the 10nm node process will be similar to that at the 14nm node, though perhaps with alternate channels. The 7nm node will be an inflection point with more innovation needed such as gate-all-around (GAA) nanowires in a horizontal array. By the 5nm node there’s no way to avoid tunnel FETs and III-V channels and possibly vertical nanowires, though self-heating issues could become very challenging. There’s no shortage of good ideas in the front end and lots of optimism that we’ll be able to make the transistors somehow, but the situation in the backend of on-chip metal interconnect is looking like it could become a bottleneck.

Guillorn extolled the virtues of embedded-memory to accelerate logic functions, as a great example of co-optimization at the chip level providing a real boost in performance at the system level. The infection at 7nm and beyond could lead to GAA Carbon Nano-Tube (CNT) as the minimum functional device. It’s limited to think about future devices only in terms of dimensional shrinks, since much of the performance improvement will come from new materials and new device and technology integration. In addition to concerns with interconnects, maintaining acceptable resistance in transistor contacts will be very difficult with reduced contact areas.

Maszara provided target numbers for a 5nm node technology to provide a 50% area shrink over 7nm:  gate pitch of 30nm, and interconnect level Metal 1 (M1) pitch of 20nm. To reach those targets, GLOBALFOUNDRIES’ cost models show that EUV with ~0.5 N.A. would be needed. Even if much of the lithography could use some manner of Directed Self-Assembly (DSA), EUV would still be needed for cut-masks and contacts. In terms of device performance, either finFET or nanowires could provide desired off current but the challenge then becomes how to get the on current for intended mobile applications? Alternative channels with high mobility materials could work but it remains to be seen how they will be integrated. A rough calculation of cost is the number of mask layers, and for 5nm node processing the cost/transistor could still go down if the industry has ideal EUV. Otherwise, the only affordable way to go may be stay at 7nm node specs but do transistor stacking.

Thein detailed why electrostatic scaling is a key factor. Parasitics will be extraordinary for any 5nm node devices due to the intrinsically higher number of surfaces and junctions within the same volume. Just the parasitic capacitances at 7nm are modeled as being 75% of the total capacitance of the chip. The device trend from planar to finFET to nanowires means proportionally increasing relative surface areas, which results in inherently greater sensitivity to surface-defects and interface-traps. Scaling to smaller structures may not help you if you loose most of the current and voltage in non-useful traps and defects, and that has already been seen in comparisons of III-V finFETs and nanowires. Also, 2D scaling of CMOS gates is not sustainable, and so one motivation for considering vertical transistors for logic at 5nm would be to allow for 20nm gates at 30nm pitch.

Kappurao reminded attendees that while there is still uncertainty regarding the device structures beyond 7nm, there is certainty in 4 trends for equipment processes the industry will need:

  1. everything is an interface requiring precision materials engineering,
  2. film depositions are either atomic-layer or selective films or even lattice-matched,
  3. pattern definition using dry selective-removal and directed self-assembly, and
  4. architecture in 3D means high aspect-ratio processing and non-equilibrium processing.

An example of non-equilibrium processing is single-wafer rapid-thermal-annealers (RTA) that today run for nanoseconds—providing the same or even better performance than equilibrium. Figure 2 shows that a cobalt-liner for copper lines along with a selective-cobalt cap provides a 10x improvement in electromigration compared to the previous process-of-record, which is an example of precision materials engineering solving scaling performance issues.

Fig. 2: ElectroMigration (EM) lifetimes for on-chip interconnects made with either conventional Cu or Cu lined and capped with Co, showing 10 times improvement with the latter. (Source: Applied Materials)

“We have to figure out how to control these materials,” reminded Kappurao. “At 5nm we’re talking about atomic precision, and we have to invent technologies that can control these things reliably in a manufacturable manner.” Whether it’s channel or contact or gate or interconnect, all the materials are going to change as we keep adding more functionality at smaller device sizes.

There is tremendous momentum in the industry behind density scaling, but when economic limits of 2D scaling are reached then designers will have to start working on 3D monolithic. It is likely that the industry will need even more integration of design and manufacturing, because it will be very challenging to keep the cost-per-function decreasing. After CMOS there are still many options for new devices to arrive in the form of spintronics or tunnel-FETs or quantum-dots.

However, Arabi reminded attendees as to why the industry has stayed with CMOS digital synchronous technology leading to design tools and a manufacturing roadmap in an ecosystem. “The industry hit a jackpot with CMOS digital. Let’s face it, we have not even been able to do asynchronous logic…even though people tried it for many years. My prediction is we’ll go as far as we can until we hit atomic limits.”

Air-gaps in Copper Interconnects for Logic

Friday, October 31st, 2014

thumbnail

By Ed Korczynski, Sr. Technical Editor, SST/SemiMD

The good people at ChipWorks have released some of the first public data on Intel’s new 14nm-node process, and the results indicate that materials limitations in on-chip electrical interconnects are adding costs. Additional levels of metal have been added, and complex “air-gap” structures have been added to the dielectric stack. Flash memory chips have already used air-gaps, and IBM has already used a subtractive variant of air-gaps with >10 levels of metal for microprocessor manufacturing, but this is the first known use of additive air-gaps for logic after Intel announced that a fully-integrated process was ready for 22nm-node chips.

Mark Bohr of Intel famously published data in 1995 (DOI:  10.1109/IEDM.1995.499187) on the inherent circuit speed limitations of interconnects, showing proportionality to the resistance (R) of the metal lines multiplied by the capacitance (C) of the dielectric insulation around the metal (Fig.1). The RC product thus should be minimized for maximum circuit speed, but the materials used for both the metal and the dielectric insulation around metal lines are at limits of affordability in manufacturing.

There are no materials that super-conduct electricity at room temperature, and only expensive and room-sized supercomputers and telecommunications base-stations can afford to use the liquid-nitrogen cooling that is needed for known superconductors to function. Carbon Nano-Tubes (CNT) and 2D atomic-layers of carbon in the form of graphene can conduct ballistically, but integration costs and electrical contact resistances limit use. Copper metal remains as the best electrical conductor for on-chip interconnects, yet as horizontal lines and vertical vias continue to shrink in cross-sectional area the current density has reached the limit of reliability. The result is the increase in the number of metal layers to 13 for 14nm-node Intel microprocessors, while IBM used 15 layers for 22nm-node Power8 chips.

Low-k Dielectrics and Pore Sizes

The dielectric constant (“k”) of silicon oxide is ~4, and ~3.5 with the addition of fluorine to the oxide (SiOF). Carbon-Doped Oxide (CDO or SiOC or SiOC:H) with k~3.0 has been integrated well into interconnect stacks. Some polymers can provide k values in the 2.0-2.7, but they cannot be integrated into most interconnects due to lack of mechanical strength, chemical resistance, and overall stability. Air has k=1, and there have been specialized chips made using metal wires floating in air, but lack of physical structure results in poor manufacturing yield and weak reliability.

A clever compromise is to use both SiOC with k~3 and air with k~1 in a stack, which results in an integrated k value weighted by the percent of the volume taken up by each phase. Porous Low-k (PLK) with 10% porosity allows for an integrated k of ~2.7 for modest improvement, but increasing porosity to just 20% for k~2.4 results in connected random pores that reduce reliability. To reliably integrate 20-30% air into SiOC, the pores cannot be random but must be engineered as discrete gaps in the structure.

In 2007, IBM announced that it would engineer air-gaps in microprocessors, but the company claimed to be using an extremely complex process for integration involving a self-assembled thin-film mask to anisotropically etch out holes between lines and then further isotropic etching to form elongated pores. Though relatively complex and expensive, this process allows for the use of any 2D layout for lines in a given metal layer.

Additive Air-gap Process-Design Integration

For fab lines that are still working with aluminum metal and additive dielectrics, air-gaps are a defect that occurs with imperfect dielectric fill. When not planned as part of the design, air-gaps formed in a lower-layer can be exposed to etchants during subsequent processing resulting in metal shorts or opens. However, Figure 2 shows that it is possible to engineer air-gaps by Chemical-Vapor Deposition (CVD) of dielectric material into line-space structures with proper process control and design layout restrictions. Twenty years ago, this editor worked for an OEM on CVD processes for dielectric fill, and the process can be tuned to be highly repeatable and relatively low-cost if a critical masking step can be avoided. In 1998, Shieh et al. from Stanford (Shieh, Saraswat & McVittie. IEEE Electron Dev. Lett., January 1998) showed proof-of-concept for this approach to lower k values.

Figure 2: CVD can be easily tuned to initially coat sidewalls (top), then pinch-off (middle), and finally form a closed pore (bottom) during one step. (Source: Ed Korczynski)

Four years ago at IEDM 2010, Intel presented details of how to engineer air-gaps using CVD. As this editor wrote at that time in an extensive analysis:

The lithographic masking step is needed for two reliability reasons. First, by excluding air-gap formation in areas near next-layer vias, alignment between layers can be more easily done. Second, wide spaces are excluded where the final non-conformal CVD step wouldnt automatically pinch-off to close the gaps; leaving full SiOC(H) in wider spaces also helps with mechanical strength. The next layer is patterned with a conventional dual-damascene flow, with the option to add air-gaps.

Now we know that Intel kept air-gaps on the metaphorical shelf by skipping use at the 22nm-node. The 2014 IEDM paper from Intel will discuss details of 14nm-node air-gaps:   two levels at 80nm and 160nm minimum pitches, yielding a 17% reduction in capacitance delays.

This process requires regularly spaced 1D line arrays as a design constraint, which may also be part of the reason for additional metal layers to allow for 2D connections through vias. Due to lithography resolution advantages with 1D “gridded” layouts, other logic fabs may soon run 1D designs at which point additive air-gaps like that used by Intel will provide a relatively easy boost to IC speeds.