Part of the  

Solid State Technology

  and   

The Confab

  Network

About  |  Contact

Headlines

Headlines

IoT Demands Part 1: EDA and Fab Nodes

The Internet-of-Things (IoT) is expected to add new sensing and communications to improve the functionality of all manner of things in the world:  bridges sensing and reporting when repairs are needed, parts automatically informing where they are in storage and transport, human health monitoring, etc. Solid-state and semiconducting materials for new integrated circuits (IC) intended for ubiquitous IoT applications will have to be assembled at low-cost and small-size in High Volume Manufacturing (HVM). Micro-Electro-Mechanical Systems (MEMS) and other sensors are being combined with Radio-Frequency (RF) ICs in miniaturized packages for the first wave of growth in major sub-markets.

To meet the anticipated needs of the different IoT application spaces, SemiMD asked leading companies within critical industry segments about the state of technology preparedness:

*  Commercial IC HVM – GLOBALFOUNDRIES,

*  Electronic Design Automation (EDA) – Cadence and Mentor Graphics,

*  IC and complex system test – Presto Engineering.

Korczynski:  Today, ICs for IoT applications typically use 45nm/65nm-node which are “Node -3″ (N-3) compared to sub-20nm-node chips in HVM. Five years from now, when the bleeding-edge will use 10nm node technology, will IoT chips still use N-3 of 28nm-node (considered a “long-lived node”) or will 45nm-node remain the likely sweet-spot of price:performance?

Timothy Dry, product marketing manager, GLOBALFOUNDRIES

In 5 years time, there will be a spread of technology solutions addressing low, middle, and high ends of IoT applications. At the low end, IoT end nodes for applications like connected smoke

detectors, security sensors will be at 55, 40nm ULP and ULL for lowest system power, and low cost. These applications will be typically served by MCUs <50DMIPs. Integrated radios (BLE, 802.15.4), security, Power Management Unit (PMU), and eFlash or MRAM will be common features. Connected LED lighting is forecasted to be a high volume IoT application. The LED drivers will use BCD extensions of 130nm—40nm—that can also support the radio and protocol-MCU with Flash.

In the mid-range, applications like smart-meters and fitness/medical monitoring will need systems that have more processing power <300DMIPS. These products will be implemented in 40nm, 28nm and GLOBALFOUNDRIES’ new 22nm FDSOI technology that uses software-controlled body-biasing to tune SoC operation for lowest dynamic power. Multiple wireless (BLE/802.15.4, WiFi, LPWAN) and wired connectivity (Ethernet, PLC) protocols with security will be integrated for gateway products.

High-end products like smart-watches, learning thermostats, home security/monitoring cameras, and drones will require MPU-class IC products (~2000DMIPs) and run high-order operating systems (e.g. Linux, Android). These products will be made in leading-edge nodes starting at 22FDX, 14FF and migrating to 7FF and beyond. Design for lowest dynamic power for longest battery life will be the key driver, and these products typically require human machine Interface (HMI) with animated graphics on a high resolution displays. Connectivity will include BLE, WiFi and cellular with strong security.

Steve Carlson, product management group director, Cadence

We have seen recent announcements of IoT targeted devices at 14nm. The value created by Moore’s Law integration should hold, and with that, there will be inherent advantages to those who leverage next generation process nodes. Still, other product categories may reach functionality saturation points where there is simply no more value obtained by adding more capability. We anticipate that there will be more “live” process nodes than ever in history.

Jon Lanson, vice president worldwide sales & marketing, Presto Engineering

It is fair to say that most IoT devices will be a heterogeneous aggregation of analog functions rather than high power digital processors. Therefore, and by similarity with Bluetooth and RFID devices, 90nm and 65nm will remain the mainstream nodes for many sub-vertical markets, enabling the integration of RF and analog front-end functions with digital gate density. By default, sensors will stay out of the monolithic path for both design and cost reasons. The best answer would be that the IoT ASIC will follow eventually the same scaling as the MCU products, with embedded non-volatile memories, which today is 55-40nm centric and will move to 28nm with industry maturity and volumes.

Korczynski:  If most IoT devices will include some manner of sensor which must be integrated with CMOS logic and memory, then do we need new capabilities in EDA-flows and burn-in/test protocols to ensure meeting time-to-market goals?

Nicolas Williams, product marketing manager, Mentor Graphics

If we define a typical IoT device as a product that contains a MEMS sensor, A/D, digital processing, and a RF-connection to the internet, we can see that the fundamental challenge of IoT design is that teams working on this product need to master the analog, digital, MEMS, and RF domains. Often, these four domains require different experience and knowledge and sometimes design in these domains is accomplished by separate teams. IoT design requires that all four domains are designed and work together, especially if they are going on the same die. Even if the components are targeting separate dice that will be bonded together, they still need to work together during the layout and verification process. Therefore, a unified design flow is required.

Stephen Pateras, product marketing director, Mentor Graphics

Being able to quickly debug and create test patterns for various embedded sensor IP can be addressed with the adoption of the new IEEE 1687 IP plug-and-play standard. If a sensor IP block’s digital interface adheres to the standard, then any vendor-provided data required to initialize or operate the embedded sensor can be easily and quickly mapped to chip pins. Data sequences for multiple sensor IP blocks can also be merged to create optimized sequences that will minimize debug and test times.

Jon Lanson, vice president worldwide sales & marketing, Presto Engineering

From a testing standpoint, widely used ATEs are generally focused on a few purposes, but don’t necessarily cover all elements in a system. We think that IoT devices are likely to require complex testing flows using multiple ATEs to assure adequate coverage. This is likely to prevail for some time as short run volumes characteristic of IoT demands are unlikely to drive ATE suppliers to invest R&D dollars in creating new purpose-built machines.

Korczynski:  For the EDA of IoT devices, can all sensors be modeled as analog inputs within established flows or do we need new modeling capability at the circuit level?

Steve Carlson, product management group director, Cadence

Typically, the interface to the physical world has been partitioned at the electrical boundary. But as more mechanical and electro-mechanical sensors are more deeply integrated, there has been growing value in co-design, co-analysis, and co-optimization. We should see more multi-domain analysis over time.

Nicolas Williams, product marketing manager, Mentor Graphics

Designers of IoT devices that contain MEMS sensors need quality models in order to simulate their behavior under physical conditions such as motion and temperature. Unlike CMOS IC design, there are few standardized MEMS models for system-level simulation. State of the art MEMS modeling requires automatic generation of behavioral models based on the results of Finite Element Analysis (FEA) using reduced-order modeling (ROM). ROM is a numerical methodology that reduces the analysis results to create Verilog-A models for use in AMS simulations for co-simulation of the MEMS device in the context of the IoT system.



Tags: , , , , , , , , , , , , , , , , , ,

Leave a Reply